===== ValiFrame USB3 Module ===== ======================================================================================================================= 2.3 [released 2020-03-06] ======================================================================================================================= 2.37 [available 2020-11-20] supported Keysight M8070B FW rev: 6.7.500.6 supported Keysight Z-Series oscilloscope FW rev: 06.50.01004 supported Keysight UXR-Series oscilloscope FW rev: 10.11.05004 supported SigTest version 3.2.11.3 for 5 Gb/s supported SigTest version 4.0.23.2 for 10 Gb/s bugfix LFPS sensitivity test fails and aborts with critical exception in some cases bugfix Wrong max spec value for LFPS t_repeat test 2.36 [available 2020-09-26] Information Updated CodeMeter Runtime to version 7.10a to fix vulnerabilities CVE-2020-14513, CVE-2020-14519, CVE-2020-14509, CVE-2020-14517, CVE-2020-16233, and CVE-2020-14515 2.35 [available 2020-09-07] bugfix Updated wrong released date of 2.34 modification LFPS Compliance test result is clearer now, by introducing 'Dut Responded' column and by adding more descriptions modification Since compliance sensitivity test goes down to 90mV now, we should decrease the calibration starting point 2.34 [available 2020-08-14] bugfix Trigger channels of Rx tests with Power on Reset training, for USB spec version 3.1 were switched bugfix Setup with a M8041A module and a M8051A module wasn't supported information Not tested online with M8051A + M8041A set up 2.33 [available 2020-07-14] bugfix Loopback training skipped during Jitter Tolerance tests bugfix Improvements to ValiframeRemote program and fix to avoid InvalidProgramException while running scripts 2.32 [available 2020-05-08] bugfix Valiframe crashes if neither M8041A-UA3 nor M8041A-0A3 License is installed on the BERT 2.31 [available 2020-04-27] bugfix System out of memory Exception during Jitter Tolerance Test on M8020A 2.30 [available 2020-03-06] modification Tested with M8070B FW rev: 6.7.500.6 modification Tested with Z-Series oscilloscope FW rev: 06.50.01004 modification Tested with UXR-Series oscilloscope FW rev: 10.11.05004 modification Tested with SigTest version 3.2.11.3 for 5 Gb/s modification Tested with SigTest version 4.0.23.2 for 10 Gb/s modification Modification of step size for LFPS Rx sensitivity test: 50mV from 1.2V to 400mV, 20mV from 400mV to fail point modification Added LFPS Rx Detect Threshold; Effective Date: Sep, 2019 -> May, 2020 modification Changed to a new BitifEye License Manager (BLM) modification 5 Gb/s and 10 Gb/s TxEQ calibration modification Added sequence controlled cdr for interactive ltssm modification Added two channel scope support modification Made the use of instrument scrambler vs. ValiFrame scrambler selectable in parameter list (Gen2 only) bugfix Project data can overwrite caldata dependent properties: after project file was loaded cal dependent values are recalculated ======================================================================================================================= 2.2 [released 2019-02-14] ======================================================================================================================= 2.24 [available 2019-09-10]: modification Tested with UXR oscilloscope FW rev. 10.05.04305 known issues Calibrations do not work with UXR FW version 10.10.04514 modification Tested with J-BERT M8070B FW rev. 6.0.210.6 modification Tested with U7243C USB3 Tx Test Application version 3.32.1.0 bugfix Signal amplitude for short channel tests can be changed again modification Introduced a "Force Retraining" property which trains the DUT after every test modification Added command to enable or disable Infiniisim graphs on scope Waveform acquisition with embedding can be significantly speed up when not showing Infiniisim graphs at UXR scopes bugfix Option "D9010DMBA" wasn't recognized as Infiniisim at calibrations using embedding bugfix Retrain parameter for Jitter Tolerance Test was not working when run togehter with other tests 2.23 [available 2019-06-03]: modification Tested with UXR oscilloscope FW rev. 10.05.04305 known issues Calibrations do not work with UXR FW version 10.10.04514 modification Tested with J-BERT M8070B FW rev. 6.0.210.6 modification Tested with U7243C USB3 Tx Test Application version 3.32.1.0 bugfix Tx Test App connection diagrams are not displayed (only fixed for scopes running with Windows 7) known issues Tx Test App connection diagrams are not displayed with Windows 10 scopes bugfix Aligned ValiFrame Tx test procedures to Tx App test tree bugfix Wrong ISI value was chosen while using tethered Type-C devices bugfix Calibrations failed while using Excel ("Could not save"-error) bugfix -3.5dB De-Emphasis Mode got removed from U7243C version bugfix If no equalization is available, the parameter is still defined and not left blank bugfix Connection diagram for USB3.0 StdB-Connector displayed correctly again bugfix 5G Compliance Tests fail after two errors now (not after one error) modification Maximum allowed second tone sj for N7015A increased to 8 (Warning still shown if above 5ps) modification Removed transfer function handling for Tx test app because it's handled by the app 2.21 [available 2019-02-28]: modification Tested with UXR oscilloscope FW rev. 10.00.04104 bugfix 5G LFPS, De-Emphasis and Generator Output Voltage Calibration and 10G Pre-Shoot, De-Emphasis and Generator Output Voltage Calibration sometimes measure only half the amplitude with UXR FW rev 10.00.04104 modification ValiFrame USB is installed in an own start menu folder "BitifEye USB" modification Analyzer CDR is disabled while training, but can be enabled through the parameter settings new Sampling rate for UXR oscilloscopes can be adjusted for calibrations using SigTest 2.20 [available 2019-02-14]: modification Tested with J-BERT M8070B FW rev. 5.0.228.4 modification Tested with scope FW rev. 6.30.00609 modification Tested with U7243C USB3 Tx Test Application version 03.32.0000 (Windows 7) modification Connection diagrams do not pop up if the setup stays the same modification Power supply and Bit2100 Switch are now shown in station configuration if selected new UXR scope support bugfix Fixed connection diagrams which include M8048A TraceBox bugfix Fixed channel handling while using tethered type-C connector bugfix Defined behaviour for partially missing licences ======================================================================================================================= 2.1 [released 2017-12-12] ======================================================================================================================= 2.13 [available 2018-08-27]: modification Tested with J-BERT M8070A FW rev. 5.0.228.4 modification Tested with scope FW rev. 6.30.00609 modification Tested with U7243C USB3 Tx Test Application version 03.32.0000 (Windows 7). modification For LTSSM no Power dividers are needed anymore bugfix N4903B TSEQ pattern was not scrambled for 10G bugfix Changed LFPS sensitivity test flow bugfix Changed content of host sequences (Added more trigger) bugfix Fixed warning messages about inconsistent calibration data in offline mode bugfix Long channel compliance test 5G was done with Diff Voltage for short channel test bugfix LFPS Tests run again on the right inputs bugfix Fixed M8000 output glitches when changing range 2.12 [available 2018-07-17]: bugfix Long channel compliance test 5G was done with Diff Voltage for short channel test 2.11 [available 2018-05-23]: bugfix On Lane 1 of LFPS Test the second Input of the Oscilloscope was used modification Added names of needed configuration procedures modification Power dividers are not needed anymore for interactive loopback training 2.10.1 [available 2017-12-18]: bugfix Rx LFPS-Tests were not running properly with J-Bert N4903 2.10 [available 2017-12-12]: modification Tested with J-BERT M8070A FW rev. 4.0.100.2 modification Tested with J-BERT N4903B FW rev. 7.64 modification Tested with scope FW rev. 4.20.0017 (Windows XP) and FW rev. 6.10.00803 (Windows 7) modification Automated configuration of Keysight N7016A and N7018A Type-C test controllers with BitifEye Remote Instruments Server (version 1.6) modification Renamed "SuperSpeed" to "5G" and "SuperSpeedPlus" to "10G" modification Call SigTest in silent mode during 10G calibrations new J-BERT generator/analyzer channel selection new Independent handling of calibration data of each J-BERT generator channel new Support of Keysight N7018A Type-C test controller new Type-C test controller selection in Station Configuration new Power-cycle automation mode "Keysight N701XA" with Keysight N7016A or N7018A Type-C test controller new Type-C dual lane full automated test mode using a J-BERT with two generator/analyzer channels and Keysight N7016A or N7018A Type-C test controller ======================================================================================================================= 2.0 [released 2016-07-06] ======================================================================================================================= 2.06 [available 2017-11-21]: bugfix Idle method for LFPS signals selected by the user is disregarded 2.05 [available 2017-08-29]: modification Tested with J-BERT M8070A FW rev. 3.7.40.2. bugfix Setting up M8020A takes a very long time and running two Rx tests in a row does not work 2.04 [available 2017-05-05]: modification Tested with J-BERT M8070A FW rev. 3.5.108.6 modification Tested with J-BERT N4903B FW rev. 7.64 modification Tested with scope FW 4.20.0017 (Windows XP) and FW 6.00.00708 (Windows 7) modification Tested with U7243B USB3 Tx Test Application version 03.20.0000 (Windows 7) modification Tested with U7243A USB3 Tx Test Application version 01.44 (Windows XP) modification Tested with N5416B USB 2.0 Tx Test Application version 03.93.0001 (Windows 7) modification Tested with N5416A USB 2.0 Tx Test Application version 03.82 (Windows XP) modification Automated configuration of Keysight N7016A Type-C Low-Speed Signal Access and Control Fixture with BitifEye Remote Instruments Server (version 1.4) modification Changed 5G de-emphasis and differential voltage calibration as described in the CTS rev. 1.0 modification Using SigTest version 3.2.11.2 for 5G Rx Calibration modification Using SigTest version 4.0.23.1 for 10G Rx Calibration new Support of M8070A LTSSM for 5G and 10G Rx tests with hosts 2.03 [available 2016-12-20]: modification Tested with J-BERT M8070A FW rev. 3.5.0.2 modification Tested with J-BERT N4903B FW rev. 7.64 modification Tested with scope FW 4.20.0017 (Windows XP) and FW 5.75.00214 (Windows 7) modification Tested with U7243B USB3 Tx Test Application version 03.00.0001 (Windows 7) modification Tested with U7243A USB3 Tx Test Application version 01.44 (Windows XP) modification Tested with N5416B USB 2.0 Tx Test Application version 03.93.0001 (Windows 7) modification Tested with N5416A USB 2.0 Tx Test Application version 03.82 (Windows XP) modification Improved connection diagrams modification Instrument set-up time optimization modification Removed "Skip J-BERT Reset" property for Super Speed and Super Speed Plus calibrations and Rx tests new Support of M8070A LTSSM for 5G and 10G Rx tests new SigTest version selection in USB Station Configuration new Automated configuration of Keysight N7016A Type-C Low-Speed Signal Access and Control Fixture with BitifEye Remote Instruments Server (version 1.2) new Customizable jitter step size at each frequency in Rx Jitter Tolerance test 2.02 [available 2016-10-25]: modification 10G random jitter and sinusoidal jitter calibrations: extended the interface to SigTest in order to use independent templates 2.01 [available 2016-10-18]: modification Tested with J-BERT M8070A FW rev. 3.1.55.14 modification Tested with J-BERT N4903B FW rev. 7.64 modification Tested with U7243B USB3 Tx Test Application version 03.00.0001 (Windows 7) modification Tested with U7243A USB3 Tx Test Application version 01.44 (Windows XP) modification Tested with N5416B USB 2.0 Tx Test Application version 03.93.0001 (Windows 7) modification Tested with N5416A USB 2.0 Tx Test Application version 03.82 (Windows XP) modification Extended jitter capability in Rx Jitter Tolerance Test bugfix Output amplitude range not set correctly in short channel Rx tests with J-BERT M8020A bugfix SigTest integration does not work on Windows XP bugfix Custom SigTest executable does not work new Added property to set the trigger threshold for Rx LFPS tests bugfix Bad scaling in the DUT parameters dialog bugfix ValiFrame does not detect that the DUT exits loopback during Rx Jitter Tolerance test bugfix Wrong connection to the USB3.1 Captive Device Fixture Type-C 2.00 [available 2016-07-06]: modification Tested with J-BERT M8070A FW rev. 3.1.55.14. modification Tested with J-BERT N4903B FW rev. 7.64. modification Tested with scope FW 4.20.0017 (Windows XP) and FW 5.60.00603 (Windows 7) modification Tested with U7243B USB3 Tx Test Application version 03.00.0001 (Windows 7) modification Tested with U7243A USB3 Tx Test Application version 01.44 (Windows XP) modification Tested with N5416B USB 2.0 Tx Test Application version 03.93.0001 (Windows 7) modification Tested with N5416A USB 2.0 Tx Test Application version 03.82 (Windows XP) modification 5G Tx tests base ID changed from 20012XX to 22200XX modification 5G Compliance Test: changed the default value of the parameter "Retrain at each jitter frequency" to false modification 5G Compliance Test: changed the order in which the sinusoidal jitter frequencies are tested, from highest (50 MHz) to lowest (500 kHz) new Added "Skip J-BERT Reset" property for Super Speed and Super Speed Plus calibrations and Rx tests in Expert Mode modification Regrouped Super Speed calibrations and added a sub node for long channel calibrations modification Reduced default link training voltage for super speed short channel tests to 800mV and made it editable in Compliance Mode modification New application name is now USB (former USB3). The current USB application supports USB 2.0, 3.0 and 3.1 new Support for Type-C connector type new Support for USB3.1 SuperSpeedPlus ======================================================================================================================= 1.5 [released 2015-01-28] ======================================================================================================================= 1.53 [available 2015-08-19]: modification Tested with J-BERT M8070A FW rev. 2.5.2.4. modification Tested with J-BERT N4903B FW rev. 7.61. modification Tested with scope FW 4.20.0017 (Windows XP) and FW 5.50.0027 (Windows 7) modification Tested with U7243B USB3 Tx Test Application version 2.1.0.0 (Windows 7) modification Tested with U7243A USB3 Tx Test Application version 1.50.0.0 (Windows 7) modification Tested with U7243A USB3 Tx Test Application version 1.44.0.0 (Windows XP) bugfix USB3 Tx SSC tests don't work with Tx application U7243B running on a scope with 13GHz bandwidth or less 1.52 [available 2015-06-02]: modification Tested with scope FW 4.20.0008 (Windows XP) and FW 5.50.0010 (Windows 7) modification Tested with J-BERT M8070A FW rev. 2.1.50.2 modification Set M8041A transition time to "moderate" if M8041A supports it modification Support of DSO V Series new Added selectable scope channels (ch1ch3 or ch2ch4) for calibration bugfix Decreased M8041A sequence download time 1.51 [available 2015-04-27]: modification Tested with J-BERT M8070A FW rev. 2.0.0.0 modification Tested with J-BERT N4903B FW rev. 7.60 modification Tested with U7243A USB3 Tx Test Application version 1.44.0.0 (Windows XP) and U7243A USB3 Tx Test Application version 1.50.0.0 (Windows 7) modification Tested with scope FW 4.20.0008 (Windows XP) and FW 5.50.0005 (Windows 7) known-issue USB3 Tx SSC tests don't work with Tx application U7243B running on a scope with 13GHz bandwidth or less. Please use the U7243A application instead or wait until Keysight provides a bugfix for the U7243B application modification For all calibrations, where the output of the data generator is directly connected to the oscilloscope, the highest possible bandwidth of the oscilloscope is used. This minimizes the ringing caused by fast transitions of the data generator (especially M8020A). For M8020A systems, which have the Adjustable ISI option, a small amount of ISI is added to slow down the transitions 1.50 [available 2015-01-28]: modification Tested with scope FW 4.20.0008 (Windows XP) and FW 5.20.0013 (Windows 7) modification Tested with U7243B USB3 Tx Test Application version 2.0.0.0 modification Tested with U7243A USB3 Tx Test Application version 1.44.0.0 (Windows XP) and U7243A PCIe Tx Test Application version 1.50.0.0 (Windows 7) modification Tested with N5416A USB3 Tx Test Application version 3.81.0.0 modification Tested with J-BERT N4903B FW rev. 7.60 and 7.61 modification Tested with J-BERT M8070A FW rev. 1.5.7.4 new Training voltage for Short Channel Rx tests can be set separately new Optional TSEQ pattern at the end of the Rx LFPS test sequence for crystal less devices new Added High Speed Rx tests for M8020A new Added analyzer equalization property for M8020A new Added Rx LFPS tests for M8020A bugfix "Clock" LFPS electrical idle method does not work anymore for some DUTs. The reason was that at the beginning of the training sequence a clock pattern instead of an static zero pattern was used. The clock pattern should only be used between the LFPS bursts bugfix User selection of LTS script files is reset to default when closing Configure DUT dialog or starting any Rx test bugfix Instrument serial numbers are not verified for Eye-Height- and TJ- -calibration and -verification ======================================================================================================================= 1.4 [released 2014-08-08] ======================================================================================================================= 1.40 [available 2014-08-08]: modification Tested with scope FW 4.20.0008 (Windows XP) and FW 5.10.0003 (Windows 7) modification Tested with U7243A USB3 Tx Test Application version 1.44.0.0 (Windows XP) and 1.50.0.0 (Windows 7) modification Tested with J-BERT N4903B FW rev. 7.50 and 7.60 modification Tested with J-BERT M8070A FW rev. 1.0.8.6 new Added M8020A J-BERT support modification ParBERT, J-BERT N4903A and Ellisys USB3 Analyzer are no longer supported. Please use version 1.33 for those instruments modification Updated to CTS Version 1.0 R2, TJ is now only verified at 50Mz SJ frequency instead of all SJ frequencies used for Rx compliance new Added Short Channel USB3 Rx Tests new USB Link Training script files can be used for loopback training (optional) modification USB Link Training Suite is used internally for loopback training instead of using pattern and sequence files new Added differential error detector connection for power on reset training method. This connection is more stable e.g. when DUT transmits with CM interference .This requires two additional power dividers. Single ended connection is still available but not default ======================================================================================================================= 1.3 [released 2013-03-13] ======================================================================================================================= 1.33 [available 2014-05-13]: bugfix If DUT is out of loopback mode and "Retrain at each Jitter Frequency" is set to "False" all remaining jitter frequencies will fail modification Last version which supports J-BERT A and ParBERT configuration bugfix ParBERT does not work with "Idle" as LFPS el. Idle Method 1.32 [available 2013-11-21]: modification Tested with scope FW 4.20.0008 (Windows XP) and FW 4.60.0005 (Windows 7) modification Tested with N5416A USB Tx Test Application version 3.81.0.0 modification Tested with U7243A USB3 Tx Test Application version 1.43.0.0 modification Tested with J-BERT FW rev. 7.40 new Added de-embedding option for Rx calibration bugfix Fixed polarity issue for high speed differential voltage calibration new Added "Micro" and "Tethered" Connector Type for DUT modification Changed default "Relax Time" to 1s and default and default "Allowed Errors" to 5 for all Rx Expert Mode tests modification Each generator setup and de-emphasis setup has its own set of calibration data new Added N4915A-005 serial bus switch support for "real" electrical idle generation. Only for JBERT B, 2nd data channel AND N4916B are required bugfix Fixed "data out of range" bug for N67xx power supplies new Added IBerReader support new Added Power Switch Automation new Connection diagrams are generated dynamically new Added Receiver LFPS tRepeat Test bugfix LFPS Rx tests don't work when DUT stays in el. idle 1.31 [available 2013-03-25]: bugfix JBERT clock pattern and ParBERT pattern are not installed 1.30 [available 2013-03-13]: new Added Loopback Training Optimization window to change LB training parameters and test LB training fast modification Rotated analyzer pattern for JBERT B SER detector to have 48 unique bits at the beginning of the pattern. Error detector syncs faster with this pattern new Added Rx LFPS Duty Cycle Test. Only available with JBERT option 002 (second data channel) new Added Rx LFPS Sensitivity Test. Only available with JBERT option 002 (second data channel) new Added high speed Rx device tests. Only available with JBERT option 002 (second data channel) bugfix Jitter calibration using EZJIT Plus does not work with DSO/X firmware version 4.1 and above bugfix Eye height calibration does not work with 80k scope new Ellisys UX280 USB3 Analyzer equalizer and sensitivity settings can be adjusted new Added power supply automation for hosts ======================================================================================================================= 1.2 [released 2011-09-01] ======================================================================================================================= 1.24 [available 2012-07-02]: modification Updated Tx tests to U7243A USB3 Tx App version 1.42 1.23 [available 2012-06-14]: new Rx Jitter Tolerance Tests: Added "retrain with jitter" and "retrain at each jitter frequency" option bugfix Selected wrong sample rate on scope for LFPS Rx Test new A warning message is displayed when DSO is selected as error detector (not compliant) bugfix JBERT LFPS trigger threshold is not updated for LFPS test new Min. failed jitter points can be display optionally at the Jitter Tolerance Test new Polarity Inversion for JBERT SER detector modification Default value for Lane Polarity Inversion for devices is now False bugfix \"Use Power Supply Automation\" is not reflected in the automated Tx Tests bugfix Oscilloscope is configured in Rx Tests with JBERT B SER even it is not used bugfix DUT TX polarity swapped at J-BERT B SER setup for host RX-test in the connection diagram 1.22 [available 2011-12-02]: bugfix LFPS idle clock pattern was written to the wrong directory when a JBERT A was used modification Updated Tx test application U7243A support to version 1.41 1.21 [available 2011-10-25]: new Force Retraining option at initialization for Jitter Tolerance and Sensitivity test bugfix Retraining does not work in Jitter Tolerance when \"User Defined Frequencies\" are selected bugfix Added a workaround for inconsistent J-BERT behaviour that prevented duty cycle variations in the ReceiverLFPS test from actually being applied 1.20 [available 2011-09-01]: new Added Vbus automation for Tx Device tests modification Replaced N4916A by N4916B in all JBERT B connection diagrams new Number of TSEQ for loopback training can be configured new Number of LFPS bursts for loopback training can be configured bugfix Clock as LFPS idle is not applied if selected in the GUI new Added LFPS Receiver Test ======================================================================================================================= 1.1 [released 2011-02-11] ======================================================================================================================= 1.12 [available 2011-05-20]: modification For Tx the de-emphasis signal converter is used to toggle the Tx test pattern. This minimizes the connection changes bugfix The expected SSC deviation from the configure DUT dialog or Rx Properties is not set on JBERT bugfix ISI Trace selection from Configure DUT dialog is ignored new Added E364xA power supply for Vbus automation new Changes for U7243A Tx App version 1.4: Added "Maximum SSC Deviation" test modification Changes for U7243A Tx App version 1.4: Removed "Unit Interval with SSC" test modification Changes for U7243A Tx App version 1.4: Renamed "SSC Deviation" test to "Minimum SSC Deviation" test 1.11 [available 2011-03-22]: modification Amplitude imbalance check can be disabled in the calibration properties modification Optimized synchronization time for J-BERT SER detector bugfix When the JBERT AUX DATA is not set to "Divided Clock" Valiframe cannot connect to N4916A/B de-emphasis signal converter bugfix At startup a warning is shown that J-BERT FW REV 6.70 or higher is required while JBERT FW REV is 7.00 1.10 [available 2011-02-11]: modification Updated to Electrical Compliance Test Specification revision 0.9 RC6 modification Receiver Sensitivity: Changed Target BER from 1e-10 to 10E-9 modification Loopback Training: Differential Voltage for Loopback Training is now calibrated to Compliance settings (eye opening and de-emphasis). Alternatively the eye-opening and de-emphasis can be adjusted for loopback training modification Receiver Compliance: Retraining at each Jitter Frequency is Default. Jitter can be turned on or off for Training. Default is on new Receiver Tests: Specification Margin for Eye-Height. The CTS 0.9 specifies e.g. for USB3 Host an Eye-Height of 180mV +5mV / -0mV. The Margin Default is +2.5mV. That means that a Differential Voltage of 180mV + 2.5mV = 182.5mV is used for receiver tests. The margin can be set to values between -0mV and 5mV new Receiver Tests: Specification Margin for Sinusoidal Jitter. The CTS 0.9 specifies e.g. a Sinusoidal Jitter Level of 200mV +0% / -10% at 4.9MHz. The Margin Default is -5%. That means that a Sinusoidal Jitter Level of 200mUI - 5% = 190mUI is used for the Receiver Tests. The Margin can be set to Values between +0% and -10% new Receiver Tests: Specification Margin for Random Jitter. The CTS 0.9 specifies a Random Jitter Level of 170mV +/-10% . The Margin Default is 0%. That means that a Random Jitter Level of 170mUI + 0% = 170mUI is used for the Receiver Tests. The Margin can be set to Values between -10% and +10%. modification Changed default calibration method for HF and LF SJ Calibration from AgilentSDA to SigTest new Total Jitter and Eye Height Verification procedures new Added selftest procedures for Version, Single Ended Output Voltage, Intra Pair Skew, SSC, Random Jitter and Sinusoidal Jitter modification Changed CDR loop bandwidth for JBERT SER detector from 10MHz to 7.5MHz new Added expected SSC deviation to receiver test properties for JBERT SER detector bugfix The name for the parameter Differential Voltage is changed to Eye-Height. The CTS is refering to Eye-Height, not Differential Voltage new Integration of LFPS AC Common Mode Voltage transmitter test new Optional de-emphasis generation with second channel of J-BERT new Receiver Data Rate Tolerance Test new For receiver jitter tolerance test start SJ can be selected for each jitter frequency in "user defined frequency mode" new New SJ frequency modes for receiver jitter tolerance test: "user defined frequencies" and "single frequency" new Power supply control for Vbus for fully automated receiver tests (devices only) new The signal between the LFPS bursts in Configure.LFPS can configured either to el. idle or a 5Gbps clock signal new Number of TS1 and TS2 can be configured for loopback training ======================================================================================================================= 1.0 [released 2010-08-16] ======================================================================================================================= 1.01 [available 2010-11-30]: modification Transmitter tests optimized for execution time. Up to 5 times faster than the previous version. bugfix Automatic pattern selection for Tx tests sets the scope back in original state after the pattern is set. Scope Tx application can continue with original setting bugfix Sample size for HF SJ calibration is increased to 8MSa. Scope firmware 3.01 needs larger sample size for EZJIT+ measurements modification Retraining for jitter tolerance test is done after SJ frequency was changed if necessary bugfix Connection diagram for JBERT B SER device test setup. Polarity of DUT Tx output was swapped 1.00 [available 2010-08-16]: new Full Tx test automation with automatic test pattern selection ======================================================================================================================= 0.0 [released 2006-07-01] ======================================================================================================================= 0.81 [available 2010-05-14]: new ParBERT support new JBERT B support new CTS version 0.9 support 0.17 [available 2009-07-07]: new Initial Version for USB3 Super Speed Host and Devices 0.01 [available 2006-07-01]: new new release